Glaze tea cup and lantern

 

 

             Coblate blue

I like think the color made it stand out more.

                      Speckled pink The cup has so mush dizines on it and stand out more.


With this glaze assignment you should have been able to try out a variety of glazes, and hopefully you found a lot of success! On your blog: 1. 2 photos of your lantern (from the side and looking into) 2. Below the photos write down the glaze(s) you used and the process you took to glaze 3. Discuss how you liked/didn't like the final result 4. 1 photo of each cup 5. Below each cup write down the glaze(s) and process 6. Discuss how you liked/didn't like the final resu

Cups

We wedge  the clay and making it in to a ball and we take it to the sink and we start to pull down the clay to make the handle. It was hard to pull it down make the handle and it kept falling off.

We could make a thicker handle, because it mint to thin to hold the cup and fall off the cup.

hand building lanter

Label your Blog post: Lantern POST 3-4 pictures of your project in progress and a picture of your finished piece. ANSWER the questions below. 1. What hand building method did we use to construct this piece. 2. What did you do to connect two pieces together? 3. Why did you choose your design? What do you like most about it? What do you like least about it? 4. What would you do differently if you did this project over again? I can't wait to see your piece glazed.

                                                             We used  the slab method  and wedge the clay and then we went to the slab machine   flatten   the clay out  and then we cut out squares and then we copied out the design out of a book and then we trace   it on the clay and then we made the sides fettling knife on four sides to fit it to  get there and we used slip and score the edges and i used a needle tool to cut out the design and we take a sponge to wipe it down and get the little pieces out to make sure pieces are out of there.

It was hard to work with hard clay and cutting out the arrows and squares and making shore the sides are same size and keeping it wet and making it cover well because it want dry out. This was not hard but I would do this a gin and It was hard to cut out the shapes and making shore its wet and it would work better for me and but i think it could made the lanter look better then what it looks like.

lanter hand build

pinch pot and cole pot andgl moled monste

                                                                     Cranberry
                                             We used prongs to dip the piece and we painted it on too.We dip more then once.and less then 30 seconds. We faced some challenges with the glaze.When we put the piece in the glaze with the prongs and the pot filled up with glaze. The glaze had air bubbled in it. When Ms. Blane tried to get the pot out of the glaze it bubbled up on her face.                

                                                                          dark green, roes orange

                   I painted the under glaze  color on before we put it in the kiln. I used a paint brush. After the under glaze we though the kiln we dipped the monster in the glaze with our hands.We  dipped the monster in the glaze for less than thirty seconds. The  glaze did not drip down the side. the glazing process went well.The glaze turned out very well. When the monster came out of the kiln it looked very shiny.As far as color vanations the green part looked a little lighter on the mohawk.On part of the side ofthe monsters face the pink color turned out a little bit lighter than  I had expected.A so the color that I thought was a rich orange turned out to be more of a yellow color than I thought.

                                               blue 

I dipped the pot  in the glaze with my hands. I dipped my pot  for auproximately 10 second. Next I painted some pant with a paint brush. The brush I used had wax resist in it so it was sticky. The glaze went on well. After the pot came out of the kiln the glaze is very very shiny. The glaze was sucessful.

                                 

Hump Mold Monster Questions

                                              Hump mold monster
                                       The mouth is very big and has sharp teeth.

                                      It has  pointy hair and pointy ears and eyes are shaped like triangles. For        texture there bumps on the  head and scraches on the  face. she is a girl.and The thing I like about  her is the  hair .  Her name is mow hock.her color is pink orange green.  I made the nose and eyes smalland the moth big.

.

HUMP MOLD MONSTER

Monster made out of clay 

L